跳到主要內容

簡易檢索 / 詳目顯示

回結果列表
研究生： 翁加旺
Chia-wang Weng
論文名稱： Ni添加對Mg17Al12合金吸放氫性質影響之研究
The effect of Ni addition on hydrogen storage properties of Mg17Al12 alloy
指導教授： 李勝隆
Sheng-Long Lee
口試委員:
學位類別： 碩士
Master
系所名稱： 工學院 - 機械工程學系
Department of Mechanical Engineering
畢業學年度： 97
語文別： 中文
論文頁數： 50
中文關鍵詞： Mg17Al12 、Ni 、XRD 、儲放氫特性
外文關鍵詞： Mg17Al12, Ni, XRD, PCI, Hydrogen storage alloys
相關次數： 點閱：11  下載：0 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • 　　本研究利用鑄造法結合退火熱處理製備高純度Mg17Al12合金，再利用球磨法製備出Mg17Al12+X wt.% Ni (X=0，10，20)合金，並透過充分活化與PCI測試，以研究該合金之吸放氫性質，期望藉由Ni的添加，以催化Mg17Al12合金，降低合金之吸放氫溫度並改善其吸放氫動力學。
    　　由活化測試與吸放氫速率測試得知，將Ni添加至Mg17Al12中有助於提升合金氫化時之氫化百分比與吸氫速率，並降低吸氫溫度。在PCI氫化測試中，含Ni之Mg17Al12合金其氫化曲線具有三個氫化平台;由XRD結果證實，經過吸放氫反應後，含Ni之Mg17Al12合金組成已轉變為Mg17Al12、純Mg、Al3Ni及Al3Ni2，其中僅Mg17Al12與純Mg參與氫化反應，因而可推測第一平台為純Mg之氫化平台，第二平台為Mg17Al12轉變為氫化物MgH2及β相(Mg2Al3)，第三平台為β相轉變為MgH2及純Al，純Mg在Mg17Al12之催化下，吸氫動力學亦獲得大幅改善。

    　　Mg17Al12 alloy was prepared by melting method followed by annealing ,and then ball-milled with Ni for 3 hours to obtain Mg17Al12- X wt.% Ni (X=0，10，20) composite. XRD results showed that no new phases formed during ball milling ,all of the diffraction peaks correspond to Mg17Al2 and Ni. In the activation test, Mg17Al12-20 wt.% Ni composite showed the most rapid absorption rate and highest hydrogenation fraction, followed by Mg17Al12-10 wt.% Ni and pure Mg17Al12 , showed that Ni addition is useful to improve the hydrogenation properties of Mg17Al12 alloy. The hydrogenation reaction of Mg17Al12-Ni composite had been clarified by PCI and XRD, after cycles of hydriding/dehydriding, the composition of composite will changed from (Mg17Al12+Ni) to (Mg17Al12+Al3Ni+ Al3Ni2+Mg), led the hydrogenation reaction to proceed in 3 stage. This behavior is clearly visible from multi- plateaux of PCI curves.

    中文摘要..................................................i 英文摘要.................................................ii 誌 謝 ...............................................iii 總 目 錄.................................................iv 圖 目 錄.................................................vi 表 目 錄.............................................. viii 一、 前言與文獻回顧.................................1 1.1 儲氫合金發展簡介.................................1 1.2 儲氫合金之種類與介紹.............................2 1.3 儲氫合金儲放氫基本原理...........................3 1.3.1 動力學性質.....................................3 1.3.2 熱力學性質.....................................5 1.4 Mg-Al儲氫合金介紹................................9 1.5 研究背景與實驗目的..............................12 二、 實驗步驟與方法................................14 2.1 製備合金流程....................................15 2.2 球磨合金流程....................................15 2.3 X 光繞射分析(X-ray diffraction methods，XRD) ...16 2.4 電子微探針分析(EPMA)............................16 2.5 合金儲放氫特性測試..............................16 2.5.1 合金活化……………………………………………………16 2.5.2 PCI曲線(Pressure-composition-isothermal curves， PCI)測試..............................................17 三、 結果與討論....................................18 3.1 微結構分析......................................18 3.2 活化測試與吸氫速率比較..........................20 3.3 PCI曲線量測與結構分析….........................27 四、 結論..........................................35 五、 未來研究與方向................................36 六、 參考文獻.....................................37

    [1]T. Graham, “On the Relation of Hydrogen to Palladium”, Journal of the Franklin Institute, Vol.87, pp.256-266, 1869.
    [2]J.J. Reilly, R.H. Wiswall,“The Reaction of Hydrogen with Alloys of Magnesium and Nickel and the Formation of Mg2NiH4”, Inorganic Chemistry, Vol.7, pp.2254-2256, 1968.
    [3]J.H.N. Vucht, F.A. Kuijpers, H.C.A.M Bruning,“Reversible Room-Temperature Absorption of Large Quantities of Hydrogen by Intermetallic Compounds”, Philips Research. Reports., Vol.25, pp.133-140, 1970.
    [4]J.J. Reilly, R.H. Wiswall, “Formation and Properties of Iron Titanium Hydride”, Inorganic Chemistry., Vol.13, pp.218-222, 1974.
    [5]K.C. Hong, “The development of hydrogen storage electrode alloys for nickel hydride batteries” Journal of power sources, Vol.96, pp. 85-89, 2001.
    [6]L. Schlapbach, A. Zuttel, “Hydrogen-storage materials for mobile applications”, Nature, Vol.414, pp.353-358, 2001.
    [7]R. Janot, L. Aymard, A. Rougier , “Fast Hydrogen Sorption Kinetics for Ball Milled Mg2Ni Alloys”, Journal of Physics and Chemistry of Solids, Vol.65, pp.529-534, 2004.
    [8]M. Martin, C. Gommel, C.Borkhat , “Absorption and Desorption Kinetics of Hydrogen Storage Alloys”, Journal of Alloys and Compounds, Vol.238, pp.193-201, 1996.
    [9]E. David, “An overview of advanced materials for hydrogen storage”, Journal of Materials Processing Technology, Vol.162-163, pp.169-177, 2005.
    [10]A. Anani, A.Visintin, K.Petrov, “Alloys for hydrogen storage in nickel/hydrogen and nickel/metal hydride batteries”, Journal of Power Sources, Vol.47, pp.261-275, 1994.
    [11]G. Sandrock, “A panoramic overview of hydrogen storage alloys from a gas reaction point of view”, Journal of Alloys and Compounds, Vol.293-295, pp.877-888, 1999.
    [12]K. Aoki, M.Kamachi, T.Masumoto, “Thermodynamics of Hydrogen Absorptionin Amorphous Zr-Ni Alloys”, Journal of Non - Crystalline Solids, Vol.61-62, pp.679-684, 1984.
    [13]B. Vigehom, J. Kjoller, B. Larsen, “Magnesium for hydrogen storage”, Journal of the Less Common Metals’, Vol.74, pp.341-350, 1980.
    [14]A. Zaluska , L. Zaluski, J.O. Strom–Olsen, “Nanocrystalline magnesium for hydrogen storage”, Journal of Alloys and Compounds, Vol.288, pp.217-225, 1999.
    [15]G. Liang, “Synthesis and hydrogen storage properties of Mg-based alloys”, Journal of Alloys and Compounds, Vol.370, pp.123-128, 2004.
    [16]L. Zhang, Z.Y. Cao, “Effect of Al content on the microstructures and mechanical properties of Mg-Al alloys”, Journals of Materials science and Engineering A,Vol.508, pp.129-133, 2009.
    [17]Murray JL. “The Al-Mg system “, Bull Alloy Phase Diagrams, Vol.3, p.60, 1982.
    [18]H. Takamura, T. Miyashita1, “Grain size refinement in Mg–Al based alloy by hydrogen treatment”, Journal of Alloys and Compounds, Vol.356-357, pp.804-808, 2003.
    [19]Anders Andreasen, “Hydrogenation properties of Mg-Al alloys” , International Journal of Hydrogen Energy, Vol.33, pp.7489-7497, 2008
    [20]C.X. Shang, M. Bououdina, Y. Song, Z.X. Guo,“Mechanical alloying and electronic simulations of (MgH2 + M) systems(M =Al, Ti, Fe,Ni, Cu, and Nb) for hydrogen storage”, International Journal of Hydrogen Energy, Vol.29, pp.73-80, 2004.
    [21]A. Andreasen, M.B. Sψrensen, R. Burkarl, “Interaction of hydrogen with an Mg-Al alloy”, Journal of Alloys and Compounds, Vol.404-406, pp.323-326, 2005.
    [22]S. Bouaricha , JP. Dodelet , D. Guay , J. Huot , S. Boily, R. Schulz,“Hydriding behavior of Mg-Al and leached Mg-Al compounds prepared by high energy ball-milling”, Journal of Alloys and Compounds, Vol.297, pp.282-293, 2000.
    [23]X.L. Wang , J.P. Tu, P.L. Zhang, X.B. Zhang, C.P. Chen, X.B. Zhao,“Hydrogenation properties of ball-milled MgH2-10 wt% Mg17Al12 composite”, International Journal of Hydrogen Energy, Vol.32, pp.3406-3410, 2007.
    [24]F. Laurencelle, J. Goyette, “Simulation of heat transfer in a metal hydride reactor with aluminium foam”, International Journal of Hydrogen Energy, Vol.32, pp.2957-2964, 2007.
    [25]Q.A Zhang, H.Y Wu, “Hydriding behavior of Mg17Al12 compound”, Materials Chemistry and Physics, Vol.94, pp.69-72, 2005.
    [26]J.-C. Crivello, T. Nobuki, S. Kato, M. Abe, T. Kuji, ”Limits of the Mg-Al γphase range by ball-milling”, Intermetallics, Vol.15,pp.1432-1437, 2007.
    [27]J.-C. Crivello, T. Nobuki, S. Kato, M. Abe, T. Kuji,“Hydrogen Absorption properties of the γ-Mg17Al12 phase and its Al richer domain”, Journal of Alloys and Compounds , Vol.446-447, pp.157-161, 2007.
    [28]H. Yabe, T.Kuji, ”Thermal stability and hydrogen absorption/ desorption properties of Mg17Al12 produced by bulk mechanical alloying”, Journal of Alloys and Compounds, Vol.433, pp.241-245, 2007.
    [29]M. Bououdina, Z.X. Guo, “Comparative Study of Mechanical Alloying of (Mg+Al) and (Mg+Al+Ni) Mixtures for Hydrogen Storage”, Journal of Alloys and Compounds, Vol.336, pp.222-231, 2002.

    QR CODE
    :::