本研究主要是利用消除流動靜止區，進一步改善儲槽粒子之流動性。對於消除流動靜止區的方法很多，其中最方便且有效的方法既在儲槽中置入阻礙物改善流場行為，雖然阻礙物的使用非常普遍，但工業界對於儲槽中置入阻礙物改善流動形態與應力分怖的相關研究還很少，傳統上仍大都以經驗的方式處理。本研究是以Johanson設計阻礙物的方法為基礎，以實驗的方法探討儲槽置入阻礙物後對流場的影響，並嘗試改變阻礙物的位置及大小，探討各種阻礙物對流場的影響。

1.Campbell, C.S., 1990, “Rapid Granular Flows,” Annu. Rev.
Fluid Mech., Vol. 22, pp. 57－92.
2.Jaeger, H.M. and Nagel, S.R., 1992, “Physics of Granular
State,” Science, Vol. 255, pp. 1523－1531
3.Cundall, P.A., 1979, “A discrete numerical model for
granular assemblies,” Geotechnique, 29, pp.47-65.
4.Neederman, R.M., 1992, Statics and Kinematics of Granular
Materials, Cambridge University Press.
5.Janssen, H.A., 1895, Versuch über Getreidedruck in
Silozellen, VDI Zeitschrift, pp.1045-1089.
6.Brown, R.L. and Hawksley, P.W.G., 1947, Fuel, 26, 159.
7.Kvapil, R., 1959, Theorie der Schüttgüterbewegung, VEB-
Verlag Thchnik, Berlin.
8.Kvapil, R., 1965, Intern. J. Rock Mech. Sci., 35.
9.Lufft, K., 1920, Druckverhältnisse in siloozellen, 2nd
revised edition, Wilhelm Ernst & Sohn.
10.Franklin, F.C. & Johanson, L.N., 1955, “Flow of granular
material through a circular orifice,” Chemicai Engng
Science 4,pp.119-129.
11.Caquot, A., 1957, “Pressure in silos,” Proc. 4th
International Conference Soil Mech. Fdn Engng London 11,191.
12.Chwetzoff, 1960, Überdrücke in silozellen, Revue: Etudes et
Réalisations, No.75,Nov./Dec..
13.Lenczner, D., 1963, “An investigation into the behaviour of
sand in a model silo,” Struct. Eng. 41, No.12,pp.389-398
and 42, No.7,pp.243-246.
14.Deutsch, G.P. & Clyde, D.H., 1967, “Flow and pressure of
granular materials in silos,” Jnl Am. Soc. Civ. Engrs,
Engng Mech. Div. 93, EM6,pp.103-125.
15.Giunta, J.S., 1969, “Flow patterns of granular materials in
flat bottom bins,” Jnl Am. Soc. Civ. Engrs 91, Series B,
No.2,pp.406-413.
16.Pariseau, W.G., 1969. “Gravity flow of ideal plastic
materials through slots,” Jnl Am. Soc. Civ. Engrs 91,
Series B, No.2.
17.Hampe, E., 1987, “Silos,” Vol.1（Grundlagen）,VEB-Verlag
Für Bauwesen, berlin.
18.Jenike, A.W., 1964, “Storage and Flow of Solids”, Bull.
123, Utah Eng. Exp. Station, Univ, Utah, Salt Lake City.
19.Schwedes, J., 1968, Fließverhalten von Schüttgütern in
Bunkern, verlag Chemie, Weinheim.
20.Jenike, A.W. & Johanson, J.R., 1971, Annual Report, Project
No. 126 — Fourth Part, “Mass Flow Bins”, and Project
126A — First Part, “Funnel Flow Bins”, Washington, DC:
American Iron and Steel Institute.
21.Tüzün, U. & Nedderman, R.M., 1985, “Investigation of The
Effects of Inserts on Flow Patterns Inside A Silo”,
Chemical Engineering Science Vol.40, No.3, pp.325-336,
Printed in Great Britain.
22.Johanson, J.R. & Kleysteuber W.K., 1966, Chem. Eng. Prog. 62
79.
23.Reisner, W. & Eisenhart-Rothe, M.W., 1971, “Bins and
Bunkers for Handling Bulk Materials”, Trans. Tech. Publ.,
Berlin.
24.Zhang, Q., Bergen, J.I. & Britton, M.G., 1997, “The Effect
of a Conical Bin Insert on Flow Patterns of Ground Feed in a
Model bin”, Canadian Agricultural Engineering, Vol.39,
No.3, pp.215-219.
25.Schwedes, J., 1983, Evolution of Bulk Solids Technology
Since 1974, Bulk Solids Handling 3(1):1-5.
26.Grossman, R.B., Towne, H.L. & Vogel, T.V., 1990, Bulk Feed
Bin Challenges, ASAE Paper 90-4013, St Joesph, MI:ASAE.
27.Johanson, J.R., 1987. Theory of Bulk Solids Flow-A
Historical Perspective, International Journal of Bulk Solids
Storage in silos 3(1):1-15.
28.Johanson, J.R., 1966, “The Use of Flow-Corrective Inserts
in Bins,” Transactions of ASME, Vol.88, No.2, pp.224-230.
29.Nedderman, R.M., 1982, Trans. Inst. Of Chem. Engrs London,
Vol.60, pp.259.
30.Schwedes, J., 1970, "Vergleichende Betrachtungen zurn
Einsatz von Scherger5ten zur Messung von
Schfittguteigenschaften," 2. Europaisches Symposium
Partikelmesstechnik, Niirnberg, Preprints, pp, 278?300.
31.Tüzün, U., Houlsby, G.T., Nedderman, R.M. and Savage, S.B.,
1982, “The flow of granular materials-II: velocity
distribution in silo flow,” Chemical Engineering Science,
Vol.37, pp.1691-1709.
32.Gardner, G.C., 1966, Chemical Engineering Science, Vol.21,
pp.261
33.Buchele, M.V. and Wynn, P., 1980, Chemical Engineering
Tripos Part 2., Research Project Report, University of
Cambridge.
34.Pariseau, W.G., and Pfleider, E.P., 1968, Trans. AIME, 241.
35.Tüzün, U., 1979, PH.D. Thesis, University of Cambridge.
36.Athey, J.D., Cutress, I.O., and Pulfer, R.F.,1966, Chemical
Engineering Science, Vol.21, pp.835.
37.Cutress, J.O. and Pulfer, R.F., 1967, Powder Technology,
Vol.1, pp.213.
38.Takahashi and Yanai, H., 1973, Powder Technology, Vol.7,
pp.205.
39.Drescher, A., 1972, “Photoelastic vertification of a
mechanical model for the flow of a granular material,” J.
Mech. Phys. Solids, 20, pp.337-351.
40.Davidson, J.F. & Nedderman, R.M., 1973, Trans. Inst. Chem.
Engrs 51 29.