現行法規對於固定污染源管制，採以被動管制之許可制度為主要政策。然針對屢遭陳情案件應確實掌握污染源排放時機並配合主動稽查，方能立即達空氣污染改善之成效。惟以往空氣污染稽查方式，皆僅以人力稽查為主，稽查人員至污染現場由於難以得知污染排放之確切時間，且空氣污染常為肉眼無法辨別，故僅能對廠內是否取得固定污染源操作許可證或是否依照許可證核定內容進行操作等行政管制面進行稽查，然此稽查模式並未能達到稽查作業所期望達成之空氣污染改善成效。
本研究針對銅箔基板製造程序、膠帶製造程序、玻璃纖維製造程序及印染整理程序共4類製程及蓄熱式廢氣焚化爐等有溫度變化之設備進行調查，藉由紅外線熱顯像儀發現各類製程於平時以肉眼查核無法發現之污染，並利用紅外線熱顯像儀監控掌握污染源不當操作時機。
經研究案例分析顯示，於廠外進行監控，皆能使稽查人員掌握主要污染時段，並於第一時間進場查核，各案例進行查核後，皆發現污染事實。經分析紅外線熱顯像儀使用之優劣狀況及成本效益，發現使用紅外線熱顯像儀對於製程中有熱變化之污染源查核確實可行，不僅成本較單純人力稽查更為低廉，更能於稽查前即充份掌握污染事證，採以突擊式稽查皆能一舉達成污染搜證之目的，以提升空氣品質管制效益，另配合告發處分及輔導改善，皆可有效減少空氣污染排放及陳情案件發生。

Existing regulations for Stationary Pollution Source control, passive control of the mining permit system as the main policy. However, for the case of repeated petitions should really grasp the timing and with the active source emissions inspection in order to immediately improve the effectiveness of air pollution. However, air pollution inspectors previous ways are only human inspectors mainly inspectors to contaminated sites because of the difficulty of the exact time that pollution emissions and air pollution often naked eye can not discern whether it can only be achieved on the plant operation stationary sources whether in accordance with the approved permit or license to operate such content for administrative control surface inspection, then this inspection inspectors operating mode and failed to achieve the desired improvement in the effectiveness of air pollution reached.
In this study, the manufacturing process for the CCL (Copper clad laminate), adhesive tape manufacturing process, glass fiber manufacturing process and dyeing and finishing process a total of four class manufacturing processes and regenerative thermal oxidizer devices such as a temperature change of the investigation, by the FLIR (Forward Looking Infrared) Radar found that various processes in peacetime to the naked eye can not discover the pollution checking and monitoring the use of FLIR to master pollution improper operation timing.
The case study analysis shows that on-site monitoring, all make major pollution inspectors time to master, and in the first time entering the audit, carried out checks each case, the facts were found contaminated, also analyzed the FLIR the pros and cons of using the position and cost-effectiveness, found that the use of FLIR for changes in the manufacturing process of hot check pollution is feasible, not only costs more affordable than a simple human inspectors, more for inspection prior to being fully grasp something pollution permits, mining inspectors have encountered in one fell swoop to assault-style pollution reached the purpose of gathering evidence in order to improve air quality control benefits, and the other with informant punishment and counseling to improve, can be effective in reducing air pollution emissions and petitions cases.

1.苗沛元，夜視新境界－新一代紅外線熱像儀簡介，軍品科技新知，第105 期，第73–84 頁，1998。
2.廖雁亭，「應用紅外線熱影像儀於製程機台電氣設備之預知保養研究-以某TFT-LCD 廠為例」，國立交通大學碩士論文，2009。
3.李春輝，應用熱像儀檢測地下空洞之研究，國立屏東科技大學碩士論文，2008。
4.許天飛，遠紅外線的效用及其評估方法，染化雜誌，第150期，第59頁，1997。
5.李洲亘，紅外線熱影像法參數設定與表層混凝土火害受損區域檢測，朝陽科技大學碩士論文，2006。
6.陳俊菁，應用攝溫影像數檢測磁磚黏貼完整性，朝陽科技大學碩士論文，2004。
7.王人鋒，紅外線熱像儀應用於FRP 補強施工品質控制參數最佳化之研究，中原大學碩士論文，2004。
8.張良真，紅外線熱影像分析在混凝土品質評估之應用，高雄應用科技大學碩士論文，2004。
9.洪國峰，舌診影像系統在疾病辨識之應用，中原大學碩士論文，2000。
10.張天鈞，從雄風飛彈到疾病偵測－談紅外線熱影像診斷系，當代醫學，2005年6月。
11.張ㄧ光，紅外線溫度量測技術，台電工程月刊，第462 期，第53-63頁，1987。
12.張光雄，主動式紅外線影像的疲勞駕駛偵測系統，國立中央大學碩士論文，2004。
13.趙桂嫻，應用紅外線熱影像偵測棒球投手運動訓練適應之研究，私立中國文化大學碩士論文，2004。
14.藍棟彥，利用紅外線熱影像探討建築缺陷的溫度變化-使用層集多重分類法，朝陽科技大學，2009
15.行政院環境保護署，固定污染源設置與操作許可證管理辦法，2007。
16.桃園縣政府環境保護局，揮發性有機物及連續自動監測污染源調查及管制計畫期末報告，2012。
17.勞工安全衛生研究所，勞工安全衛生簡訊，第76期，第13-15頁，2006。
18.陳清涼、黃冬梨、徐啟銘，石油季刊，44卷4期，第67-79頁，2008。
19.Levar,J. M. and Hamilton, H. R.,“Nondestructive Evaluation of Carbon Fiber-Reinforced Polymer-Concrete Bond Using Infrared Thermography,＂ACI MATERIALS JOURNAL / January-February，pp 63-72,2003.
20.Luong,M,”Fatigue limit evaluation of metals using an inftrared thermographic technique”, Mechanics of Materials ,Vol. 28, pp. 155-163,1998.