跳到主要內容

簡易檢索 / 詳目顯示

回結果列表
研究生： 陳永斌
Yong-Bin Chen
論文名稱： 微量Sc、Zr對Al-4.6Cu-0.3Mg-0.6Ag合金微結構與機械性質之影響
Effect of Minor Sc and Zr on the Microstructure and Mechanical Properties of Al-4.6Cu-0.3Mg-0.6Ag Alloys
指導教授： 李勝隆
Sheng-Long Lee
口試委員:
學位類別： 碩士
Master
系所名稱： 工學院 - 機械工程學系
Department of Mechanical Engineering
畢業學年度： 92
語文別： 中文
論文頁數： 44
中文關鍵詞： Al-Cu-Mg-Ag合金 、Sc 、W相
外文關鍵詞： W phase, Al-Cu-Mg-Ag alloys, Sc
相關次數： 點閱：8  下載：0 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • Al-Cu-Mg-Ag合金為一高強度鋁合金，藉由Ω相及θ’的析出而達到析出強化的效果。在純鋁或鋁合金中添加Sc元素，可使合金之晶粒細化；且有效提升合金之再結晶溫度，抑制合金發生再結晶；經高溫時效處理後，亦有Al3Sc析出相形成，可提升合金強度。在合金中同時添加Sc及Zr，可減少Sc使用量，亦可得到良好的改良效果。
    本實驗於Al-4.6Cu-0.3Mg-0.6Ag合金中分別添加0.6Sc及0.35Sc +0.07Zr，施以T7時效熱處理，探討Sc、Zr元素對合金微結構與機械性質之影響。利用光學顯微鏡(OM)、掃描式電子顯微鏡(SEM)、穿透式電子顯微鏡(TEM)、微差掃描熱分析儀(DSC)、導電度(%IACS)、硬度試驗、拉伸試驗(Tensile Test)等方法，探討微結構的變化與材料機械性質之關係。
    結果顯示，合金中添加0.6Sc或0.35Sc +0.07Zr時，因Al3Sc及Al3(ScxZr1-x)晶出相的形成，使晶粒明顯細化。此外含Sc的合金於鑄態時即有W(Al8.5-4Cu6.6-4Sc)相形成，且無法經由固溶處理回溶於基地內，因而降低基地內Cu元素固溶量，使得T7熱處理後Ω及θ’ 相析出量降低，造成合金硬度及強度降低，但延性提升。合金中並未發現Al3Sc析出相的形成。

    總目錄 謝誌………………………………………………………………………I 摘要……………………………………………………………………II 總目錄…………………………………………………………………III 圖目錄…………………………………………………………………V 表目錄…………………………………………………………………VII 壹、前言…………………………………………………………………1 1. Al-Cu-Mg-Ag合金簡介………………………………………1 2. Al-Cu-Mg-Ag合金之析出強化相……………………………2 3. Cu/Mg比對Al-Cu-Mg-Ag合金析出之影響………………….4 4. 鋁合金添加Sc元素之文獻回顧………………………………4 5. Al-Cu合金中添加Sc之影響…………………………………8 6. 實驗目的及合金設計………………………………………11 貳、實驗步驟與方法…………………………………………………13 一、合金配製、加工及熱處理…………………………………14 1. 合金配製與成分分析…………………………………14 2. 熱處理…………………………………………………14 二、微結構分析…………………………………………………15 1. OM金相觀察……………………………………………15 2. 導電度(%IACS)量測……………………………………15 3. 微差掃瞄熱分析儀(DSC) ………………………………15 4. 掃瞄式電子顯微鏡(SEM) ……………………………16 5. 電子微探儀(EPMA) ……………………………………16 6. 穿透式電子顯微鏡(TEM) ……………………………16 三、機械性質分析………………………………………………16 1. 硬度試驗………………………………………………17 2. 拉伸試驗………………………………………………17 參、結果與討論………………………………………………………18 1. 微結構分析……………………………………………………18 1.1 金相觀察、能量散佈光譜儀(EDS)及 電子微探儀(EPMA)分析………………………………18 1.2 微差掃瞄熱分析(DSC)及穿透式電子顯微鏡(TEM) 之觀察分析……………………………………………25 1.3 導電度(%IACS)分析……………………………………30 2. 機械性質分析…………………………………………………33 2.1 硬度試驗及拉伸試驗…………………………………33 肆、結論………………………………………………………………38 伍、未來研究方向……………………………………………………39 陸、參考資料…………………………………………………………40 圖目錄 圖1.1 Cu3Au的單位晶格結構示意圖…………………………………5 圖1.2 Al-Sc部分二元相圖………………………………………………5 圖1.3 Al3Zr的L12結構示意圖…………………………………………6 圖1.4 慢速冷卻下Al3Sc晶粒的表面形態……………………………7 圖1.5 Al3Sc的發展示意圖………………………………………………7 圖1.6 快速冷卻(~100 K s-1)下Al3Sc顆粒的表面形態………………7 圖1.7 快速冷卻下Al3Sc顆粒細胞突狀(cellular-dendrite) 結構概要圖………………………………………………………8 圖1.8 鋁-過渡元素再結晶溫度對過渡元素含量比較圖……………9 圖1.9 各合金中添加Sc提升降伏強度之關係圖………………………9 圖1.10 Al-Cu-Sc三元相圖……………………………………………11 圖2.1 實驗流程圖……………………………………………………13 圖2.2 板狀拉伸試片規格……………………………………………17 圖3.1 不同Sc及Zr含量之Al-Cu-Mg-Ag合金於鑄態之 金相圖及晶粒結構……………………………………………19 圖3.2 合金B經固溶處理後之SEM金相圖…………………………20 圖3.3 不同Sc及Zr含量之Al-Cu-Mg-Ag合金經均質化處理後 之金相圖………………………………………………………22 圖3.4 不同Sc及Zr含量之Al-Cu-Mg-Ag合金經固溶處理 之金相圖及晶粒結構…………………………………………23 圖3.5 合金A、B、C經固溶處理、自然時效一天後 之DSC曲線……………………………………………………26 圖3.6 合金B、C經固溶處理、自然時效一天後，以20℃/min 升溫至400℃後水淬之TEM影像圖與繞射圖………………28 圖3.7 合金A、B、C於T7人工時效後之TEM影像圖 與繞射圖………………………………………………………29 圖3.8 合金A、B、C於固溶處理後、自然時效一天 及人工時效處理之導電度曲線(%IACS) ……………………31 圖3.9 合金A、B、C經185℃×5hr(T7)處理後之拉伸破斷面…………36 圖3.10 合金A、B、C經固溶處理、自然時效一天及 人工時效處理之硬度曲線……………………………………37 表目錄 表2.1 實驗配製之Al-Cu-Mg-Ag合金成分…………………………14 表3.1 合金A、B、C經固溶處理後，基地處Cu、Sc元素含量 之電子微探儀(EPMA)分析結果………………………………24 表3.2 合金A、B、C於固溶處理、自然時效一天後， Ω相及θ’相析出熱量及析出峰值溫度………………………28 表3.3 合金A、B、C於固溶處理後、自然時效一天 及人工時效處理後之導電度量測值(%IACS) ………………31 表3.4 合金A、B、C於固溶處理、自然時效一天 及人工時效處理後之硬度量測值(HRB) ……………………34 表3.5 合金A、B、C經185℃×5hr(T7)處理後之拉伸性質……………36

    1. J. R. Davis, “ASM Specialty Handbook : Aluminum and Aluminum Alloys”, ASM International, 1993, pp. 1-17
    2. R. E. Reed-Hill and R. Abbaschian, “Physical Metallurgy Principles”, 3rd ed., PWS Publishing Company, 1991, pp. 697-698
    3. A. Wilm, Metallurgie, 8, 223, 1911
    4. S. P. Ringer, K. Hono, T. Sakurai, and I. J. Polmear, “Cluster Hardening in an Aged Al-Cu-Mg Alloy”, Scripta Materialia, Vol. 36, No. 5, 1997, pp. 517-521
    5. J. Raffin, US Patent No. 3475166, Oct. 26, 1969
    6. J. R. Davis, “ASM Specialty Handbook : Aluminum and Aluminum Alloys”, ASM International, 1993, pp. 88-220
    7. J. E. Hatch, “Aluminum Properties and Physical Metal”, Ch.8, pp.320~350, ASM (1984)
    8. A .L. Kearney and J.Raffin, “Mechanical Properties of Aluminum Castings Alloys X206.0-t4 and XA206.0-t7 vs Comparable Alloys at Various Cooling Rates”, AFS Transications, 1977 ,pp. 559-570
    9. I. J. Polmear and M. J. Couper, “Design and Development of an Experimental Wrought Aluminum Alloy for Use at Elevated Temperatures”, Metallurgical Transactions A, Vol. 19A, 1998, pp.1027-1035
    10. J. R. Davis, “ASM Specialty Handbook : Aluminum and Aluminum Alloys”, ASM International, 1993, p. 71
    11. I. J. Polmear, G. Pons, Y. Barbaux, H. Octor, C. Sanchez, A. J. Morton, W. E. Borbidge, and S. Roger, “After Concorde : Evaluation of Creep Resistant Al-Cu-Mg-Ag Alloys”, Materials Science and Technology, Vol. 15, 1999, pp. 861-868
    12. B. C. Muddle and I. J. Polmear, “The Precipitate Ω Phase in Al-Cu-Mg-Ag Alloys”, Acta Metallurgica, Vol. 37, No. 3, 1989, pp. 777-789
    13. K. M. Knowles and W. M. Stobbs, “The Structure of {111} Age-Hardening Precipitates in Al-Cu-Mg-Ag Alloys”, Acta Crystallographica B, B44, 1988, pp. 207-227
    14. S. P. Ringer, W. Yeung, B. C. Muddle, and I. J. Polmear, “Precipitate Stability in Al-Cu-Mg-Ag Alloys Aged At High Temperatures”, Acta Metallurgica et Materialia, Vol. 42, No. 5, 1994, pp. 1715-1725
    15. K. Hono, N. Sano, S. S. Babu, R. Okano, and T. Sakurai, “Atom Probe Study of the Precipitation Process in Al-Cu-Mg-Ag Alloys”, Acta Metallurgica et Materialia, Vol. 41, No. 3, 1993, pp. 829-838
    16. R. K. Wyss and R. E. Sanders, “Microstructure-Property Relationship in a 2xxx Aluminum Alloy with Addition”, Metallurgical Transactions A, Vol. 19A, 1988, pp. 2523-2530
    17. M. Takeda, Y. Madea, A. Yoshida, K. Yabuta, S. Konuma, and T. Endo, “Discontinuity of G. P.(I) Zone and θ’’-phase in an Al-Cu Alloy”, Scripta Materialia, Vol. 41, No. 6, 1999, pp. 643-649
    18. A. Grag, Y. C. Chang, and J. M. Howe, “Precipitation of the Ω Phase in an Al-4.0Cu-0.5Mg Alloy”, Scripta Metallurgica et Materialia, Vol. 24, 1990, pp. 677-680
    19. G. W. Lorimer, in Precipitation Processes in Solids (edit by K. C. Russell and H. I. Aaronson), T. M. S.-A. I. M. E., Warrendale, Pa, 1978, pp. 87-119
    20. A. K. Mukhopadhyay, “Nucleation of Ω phase in an Al-Cu-Mg Alloy Containing Small Addition of Ag”, Materials Transactions, JIM, Vol. 38, No. 5, 1997, pp. 478-482
    21. J. A. Taylor, B. A. Parker, and I. J. Polmear,“Precipitation in Al-Cu-Mg-Ag Casting Alloy”, Metal Science, Vol. 12, No. 10, 1978, pp. 478-482
    22. K. Hono, T. Sakurai, and I. J. Polmear, “Pre-Precipitate Clustering in an Al-Cu-Mg-Ag Alloy, Scripta Metallurgica et Materialia”, Vol. 30, No. 6, 1994, pp. 695-700
    23. L. Reich, M. Murayama, and K. Hono, “Evolution of Ω Phase in an Al-Cu-Mg-Ag Alloy – A Three-Dimension Atom Probe Study”, Acta Materialia, Vol. 46, No. 17, 1998, pp. 6053-6062
    24. S. P. Ringer., K. Hono, I. J. Polmear, and T. Sakurai, “Nucleation of Precipitates in Aged Al-Cu-Mg-(Ag) Alloys with High Cu:Mg Ratios”, Acta Materialia, Vol. 44, No. 5, 1996, pp. 1883-1898
    25. O. Beffort, C. Solenthaler, P. J. Iggovitzer, M. O. Speidel, “High Toughness and High Strength Spray-Deposited AlCuMgAg-Base Alloys for Use at Moderately elevated temperatures”, Materials Science & Engineering A, Vol. A191, 1995, pp. 121-134
    26. L. D. Castillo and E. J. Lavernia, “Microstructure and Mechanical Behavior of Spray-Deposited Al-Cu-Mg(-Ag-Mn) Alloys”, Metallurgical and Materials Transactions A, Vol. 31A, 2000, pp. 2287-2298
    27. V. G. Davydov, T. D. Tostove, V. V. Zakharov, Y. A. Filatov, and V. I. Yelagin, “Scientific Principle of Making an Alloying Addition of Scandium to Aluminium Alloys”, Materials Science and Engineering A, Vol. A280, 2000, pp. 30-36
    28. L. K. Lamikov and G. V. Samsonov, “Soviet Non-Ferrous Metals Res.”(USSR), 1964, 9, 79
    29. R. W. Cahn and P. Haasen, Physical Metallurgy, 4th ed., Vol. I, North-Holland, 1996, Chapter 4, pp. 205-370
    30. K. A. Gschneidner, F. W. Calderwood, Bull. Alloy Phase Diag. 10, 1989, p. 34
    31. A. F. Norman, P. B. Prangnell, and R. S. McEwen, “The Solidification Behavior of Dilute Aluminum-Scandium Alloys”, Acta Materialia, Vol. 46, 1998, pp. 5715-5732
    32. Z. Yin, Q. Pan, Y. Zhang, and F. Jiang, “Effect of Minor Sc and Zr on the Microstructure and Mechanical Properties of Al-Mg Based Alloys”, Materials Science & Engineering A, Vol. A280, 2000, pp. 151-155
    33. K. B. Hyde, A. F. Norman, and P. B. Pragnell, “The Effect of Cooling Rate on the Morphology of Primary Al3Sc Intermetallic Particles in Al-Sc Alloys”, Acta Materialia, Vol. 49, 2001, pp. 1327-1337
    34. V. Ocenasek and M. Slamova, “Resistance to Recrystallization Due to Sc and Zr Addition to Al-Mg Alloys”, Materials Characterization, Vol. 47,2001, pp. 157-162
    35. D. N. Seilman, E. A. Marquis, and D. C. Dunand, “Precipitation Strengthening at Ambient and Elevated Teperature of Heat-Treatable Al(Sc) Alloys”, Acta Materialia, Vol. 50, 2002, pp. 4021-4035
    36. “Applications of Scandium In Al-Sc Alloys”, http://www/scandium.org/Sc-Al.html
    37. M. L. Kharakterova, “Phase Composition of Al-Cu-Sc Alloys at Temperatures of 450 and 500℃”, Izvestiya Akademii Nauk SSSR. Metally, No. 4,1991, pp. 195-199
    38. M. L. Kharakterova, D. G. Eskin, and L. S. Toropova, “Precipitation Hardening in Ternary Alloys of the Al-Sc-Cu and Al-Sc-Si Systems”, Acta Metallurgica et Materialia, Vol. 42, No. 7, 1994, pp. 2285-2290
    39. V. V. Zakharov and T. D. Rostova, “On the Possibility of Scandium Alloying of Copper-Containing Aluminum Alloys”, Metal Science and Heat Treatment, Vol. 37, Nos. 1-2, 1995, pp. 65-69
    40. A. F. Norman, K. Hyde, F. Costello, S. hompson, S. Birley, and P. B. Prangnell, “Examination of the Effect of Sc on 2000 and 7000 Series Aluminium Alloy Castings : for Improvements in Fusion Welding”, Materials Science and Engineering A, Vol. A354, 2003, pp.188-198
    41. K. Yu, W. Li, S. Li, and J. Zhao, “Mechanical Properties and Microstructure of Aluminum Alloy 2618 with Al3(Sc, Zr) Phases”, Materials Science and Engineering A, Vol. A368, 2004, pp. 88-93
    42. 簡朝棋，“A201鋁合金添加稀士元素後之機械性能研究”，國立臺灣大學材料科學與工程學研究所碩士論文，2002
    43. ASTM B597-83, Annual Book of ASTM Standards, Vol. 02.02, 1984
    44. ASTM E112-88, Annual Book of ASTM Standards, Vol. 03.01, 1990
    45. ASTM B557M-81, Annual Book of ASTM Standards, Vol. 03.01, 1991
    46. A. K. Mukhopadhyay, “On the Nature of the Second Phase Particles Present in an As-Cast Al-Cu-Mg-Ag Alloy”, Scripta Materialia, Vol. 41, 1999, pp. 667-672
    47. A. K. Mukhopadhyay, “Compositional Characterization of Cu-Rich Phase Particles Present in As-Cast Al-Cu-Mg-(Li) Alloys Containing Ag”, Metallurgical and Materials Transactions A, Vol. 30A, 1999, pp. 1693-1704
    48. V. I. Elagin, V. V. Zakharov, and T. D. Rostova, “Scandium-Alloyed Aluminum Alloys”, Metal Science and Heat Treatment, Vol. 1, 1992, pp. 37-45
    49. Y. Harada and D. C. Dunand, “Microstructure of Al3Sc with Ternary Transition-Metal Additions”, Materials Science and Engineering A, Vol. A329-331, 2002, pp. 686-695
    50. 張志鴻，“銀含量對於A201鑄造鋁合金Ω相析出影響”，國立中央大學機械工程研究所碩士論文，2000
    51. S. P. Ringer, B. C. Muddle, and I. J. Polmear, “Effects of Cold Work on Precipitation in Al-Cu-Mg-(Ag) and Al-Cu-Li-(Mg-Ag) Alloys”, Metallurgical And Materials Transactions A, Vol. 26A, 1995, pp. 1659-1671
    52. G. M. Novotny, A. J. Ardell, “Precipitation of Al3Sc in Binary Al-Sc Alloys”, Materials Science and Engineering A, Vol. A318, 2001, pp. 144-154
    53. 莊雅傑，“Cu/Mg比與熱處理對Al-Cu-Mg-Ag合金應力腐蝕性之影響”，國立中央大學機械工程研究所碩士論文，2002
    54. S. Abis, P, Mengucci, and G. Riontino, “A Study of the High-Temperature Ageing of Al-Cu-Mg-Ag Alloy A201”, Philosophical Magazine B, Vol. 67, No. 4, 1993, pp. 465-484
    55. 劉國雄，林樹均，李勝隆，鄭晃忠，葉均蔚，“工程材料科學”，全華科技圖書股份有限公司，1999，pp. 399-432

    QR CODE
    :::