跳到主要內容

簡易檢索 / 詳目顯示

回結果列表
研究生： 許世勳
Hsu-Shih hsun
論文名稱： 大面積放電加工技術之研究
Study of Electrical Discharge Machining by a large scale
指導教授： 顏炳華
Piin-Hwa Yan
口試委員:
學位類別： 碩士
Master
系所名稱： 工學院 - 機械工程學系在職專班
Executive Master of Mechanical Engineering
畢業學年度： 100
語文別： 中文
論文頁數： 77
中文關鍵詞： 磁場 、鋁粉 、加工液 、放電加工 、大面積
外文關鍵詞： EDM, large-area, magnetic field, Al -powder, worki
相關次數： 點閱：16  下載：0 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • 大面積放電加工因排渣路徑長，加工屑排除不易，容易造成放電集中，導致材料移除率降低，所以本論文主要以改善加工屑排除不易問題及提升材料移除率為研究方向。針對加工屑排除不易的問題，我們提出兩種輔助機制來幫助加工屑排除，一種為在加工液裡添加鋁粉，使加工間隙加大增加流動空間、加工屑變小使移動性更好，另一種則是在工件兩側增設磁鐵加速加工屑排出，另外我們再將這兩種輔助機制同時應用於放電加工作業，探討材料移除率是否有再進一步提升。
    研究結果顯示，以較佳的參數進行放電加工時，無輔助機制加工後的工件表面會產生加工屑與碳渣累積現象，電極直徑30mm、40mm、55mm加工30min後的材料移除率分別為0.70g/min、0.69g/min、0.20g/min；在添加鋁粉輔助下材料移除率分別為0.82g/min、0.77g/min、0.72g/min，且工件表面已無加工屑與碳渣堆積；在磁場輔助下的材料移除率分別為0.96g/min、0.83g/min、0.70g/min，工件表面同樣無加工屑與碳渣堆積；在同時應用添加鋁粉與磁場輔助的加工後材料移除率則分別為1g/min、0.93g/min、0.76g/min，工件表面亦未發現加工屑與碳渣堆積。從材料移除率及表面狀態得知三種輔助機制都能改善加工屑排除不易問題及提升材料移除率，其中又以同時應用添加鋁粉與磁場輔助加工後的效果最佳。

    Due to EDM have low working speed defect,working debris weren’t easily flushed and also debris deposit between electrode and work. In order to solve this problem, We propose three solutions .First ,We add aluminum powder in the working fluid can increase the gap distance between the electrode and workpiece and wastes bits can become small quality .Second , Add the magnetic field on both sides of the workpiece, increasing processing speed of debris flow. Third, while increasing the magnetic field and adding aluminum powder in the EDM, to enhance the material removal rate.
    From the experiment results, The use of better methods of processing parameters and no improvement of the workpiece surface will have a processing chip accumulation phenomenon. 30min after processing, electrode diameter, 30mm, 40mm, 55mm material removal rates were 0.70g/min, 0.69g/min, 0.20g/min;The first Techniques experiment results, Add aluminum material removal rates were 0.82g/min, 0.77g/min, 0.72g/min, and the workpiece surface did not chip accumulation phenomenon; Magnetic field-assisted material removal rates were 0.96g/min, 0.83g/min, 0.70g/min, and the workpiece surface did not chip accumulation phenomenon; Add aluminum powder processed with the magnetic field-assisted material removal rates were 1g/min, 0.93g/min, 0.76g/min, and the workpiece surface did not chip accumulation phenomenon. Three kinds of improvements can make the process smooth chip flow and enhance the material removal rate. Add aluminum powder and add magnet while the best results after processing

    摘 要 i ABSTRACT ii 謝誌 iii 目錄 iv 圖目錄 vii 表目錄 ix 第一章 緒論 1 1-1 研究背景 1 1-2 研究目的 2 1-3 研究方法 2 1-4 文獻回顧 3 第二章 實驗原理 6 2-1放電加工原理 6 2-1-1 放電加工簡介 6 2-1-2 放電加工的材料移除機制 7 2-1-3 放電加工參數及其影響 10 2-1-4 放電加工特性 12 2-2添加鋁粉改善加工效率原理 14 2-3磁場輔助改善加工效率原理 15 3-1實驗設備 16 3-1-1 放電加工機 16 3-1-2 電磁加熱攪拌器 17 3-1-3 數位示波器 17 3-1-4 超音波洗淨機 18 3-1-5 表面粗糙儀 18 3-1-6 CNC線切割放電加工機 19 3-1-7 低真空掃描式電子顯微鏡 19 3-1-8 電子天平 20 3-2 實驗材料 21 3-2-1 電極材料 21 3-2-2 工件材料 22 3-2-3 放電加工液 23 3-2-4 鋁粉 23 3-2-5 釹鐵硼磁石 24 3-3 實驗流程 25 3-4 實驗步驟 26 第四章 結果與討論 27 4-1 加工參數對於材料移除率的影響 27 4-1-1 放電電流的影響 27 4-1-2 脈衝時間的影響 28 4-1-3 衝擊係數的影響 29 4-1-4 基礎參數選定 30 4-2 加工參數對於表面粗糙度的影響 31 4-2-1 放電電流的影響 31 4-2-2 脈衝時間的影響 32 4-2-3 衝擊係數的影響 33 4-3 加工參數對於表面形貌的影響 35 4-4 添加鋁粉的改善效果 39 4-5 增加磁場的改善效果 47 4-6添加鋁粉與磁場輔助混合加工的改善效果 55 4-7 綜合討論改善成效 62 第五章 結論 64 參考文獻 65

    1. S. H. Lee, X. P. Li, Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide, “Journal of Materials Processing Technology”,Vol.115, pp.344-358, 2001.
    2. Y. F. Tzeng and N. H. Chiu, Two-Phase Parameter Design for the Optimisation of the Electrical-Discharge Machining Process Using a Taguchi Dynamic Experiment, “Int J Adv Manuf Technol”,Vol.21,pp. 1005–1014, 2003.
    3. H. T. Lee, T. Y. Tai, Relationship between EDM parameters and surface crack formation, “Journal of Materials Processing Technology” ,Vol.142,pp. 676–683, 2003.
    4. I. Puertas, C.J. Luis, A study on the machining parameters optimisation of electrical discharge machining, “Journal of Materials Processing Technology” ,Vol.143–144 , pp. 521–526, 2003.
    5. P. M. George, B. K. Raghunath, L. M. Manochac, Ashish M. Warrier, EDM machining of carbon–carbon composite—a Taguchi approach, “Journal of Materials Processing Technology” ,Vol.145, pp.66–71, 2004.
    6. H. Ramasawmya,, L. Blunt, Effect of EDM process parameters on 3D surface topography, “Journal of Materials Processing Technology” ,Vol.148 ,pp155–164,2004.
    7. S Singh, S. Maheshwari, P. C. Pandey, Some investigations into the electric discharge machining of hardened tool steel using different electrode materials, “Journal of Materials Processing Technology” ,Vol.149 ,pp272–277,2004.
    8. C Fenggou, Y Dayong, The study of high efficiency and intelligent optimization system in EDM sinking process, “Journal of Materials Processing Technology” ,Vol.149 ,pp83–87.,2004.
    9. I. Puertas, C. J. Luis, L. Álvarez, Analysis of the influence of EDM parameters on surface quality, MRR and EW of WC–Co, “Journal of Materials Processing Technology” ,Vol.153–154 ,pp1026–1032,2004.
    10. P. Narender Singh, K. Raghukandan , B. C. Pai, Optimization by Grey relational analysis of EDM parameters on machining Al–10%SiCP composites, “Journal of Materials Processing Technology” ,Vol.155–156 ,pp.1658–1661,2004.
    11. I. Puertas, C. J. Luis, G. Villa, Spacing roughness parameters study on the EDM of silicon carbide, “Journal of Materials Processing Technology” ,Vol.164–165 ,pp.1590–1596,2005.
    12. F. L. Amorima, W. L. Weingaertner, The influence of generator actuation mode and process parameters on the performance of finish EDM of a tool steel, “Journal of Materials Processing Technology”,Vol.166,pp. 411–416,2005.
    13. M. Kiyak and O. Çakır, Examination of machining parameters on surface roughness in EDM of tool steel, “Journal of Materials Processing Technology” ,Vol.191 ,pp.141-144,2007.
    14. Özlem Salman and M. Cengiz Kayacan, Evolutionary programming method for modeling the EDM parameters for roughness, “Journal of Materials Processing Technology” ,Vol.200 ,pp.347-355,2008.
    15. 洪永洲，「整束電極在大面積放電加工之研究」，雲林科技大學碩士論文，2004。
    16. 楊錫閔，「大面積放電加工之電極改良製作及其加工特性研究」，國防大學中正理工學院碩士論文，2005。
    17. 呂育廷，「同軸噴吸機制應用於深孔及大面積放電加工之研究」，雲林科技大學碩士論文，2007。
    18. H. Narumiya, N. Mohri, N. Satio, H. Ootake, Y. Tsunekawa, T. Takawashi and K. Kobayashi, EDM by Powder Suspended Working Fluid, Proceedings of International symposium for Electro-Machining, “The Japan Society of Electrical-Machining Engineers”, pp.5-8, 1989.
    19. B.H. Yan, S.L. Chen, Effect of dielectric with suspended aluminum powder on EDM, “J. of the Chinese Society of Mechanical Engineers”, Vol.14, No.3, pp.307-312, 1993.
    20. W. S. Zhao, Q. G. Meng and Z. L. Wang, The application of research on powder mixed EDM in rough machining,“Journal of Materials Processing Technology” ,Vol.129 ,pp. 30-33,2002.
    21. H.K. Kansal, Sehijpal Singh and Pradeep Kumar, Effect of Silicon Powder Mixed EDM on Machining Rate of AISI D2 Die Steel, “Journal of Manufacturing Processes” ,Vol.9 ,pp.13-22,2007.
    22. Gunawan Setia Prihandana, Muslim Mahardika, M. Hamdi, Y.S. Wong and Kimiyuki Mitsui, Effect of micro-powder suspension and ultrasonic vibration of dielectric fluid in micro-EDM processes—Taguchi approach “International Journal of Machine Tools and Manufacture”,Vol.49,pp. 1035-1041,2009.
    23. 鄭宜峰，「純水中的電解現象分析與大電流放電加工特性研究」，國立中央大學碩士論文，2008。
    24. 周國華，「旋轉圓盤電極對 1050 鋁微細槽放電加工特性之研究」，國立中央大學碩士論文，2001。

    QR CODE
    :::