跳到主要內容

簡易檢索 / 詳目顯示

研究生: 曹正翰
Cheng-Han Tsao
論文名稱: 低漏電流與高崩潰電壓大面積矽偵測器製程之研究
Studies on Reducing Leakage Current And Increasing Breakdown Voltage of Large-Area Silicon Detector
指導教授: 洪志旺
Jyh-Wong Hong
口試委員:
學位類別: 碩士
Master
系所名稱: 資訊電機學院 - 電機工程學系
Department of Electrical Engineering
畢業學年度: 89
語文別: 中文
論文頁數: 74
中文關鍵詞: 大面積矽偵測器單面偵測器低漏電流與高崩潰電壓高能物理實驗
外文關鍵詞: Large-Area Silicon Detector, single-side Silicon Detector, Low Leakage Current And High Breakdown Voltage, high-energy phyical experiment
相關次數: 點閱:12下載:0
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

  • 首先,針對偵測器正面的氧化層、護層(passivation layer)和在偵測器背面使用砷離子佈植或POCl3預置擴散驅入技術來比較不同結構和製程對偵測器特性的影響。其實驗結果簡述如下:
    1. 由於氧化層應力的關係,使得覆蓋氧化層的元件具有較高的漏電流和較低的崩潰電壓。
    2. 同理由於應力的影響,有護層的偵測器具有較高的漏電流。但是,沒有護層的偵測器就無法預防水氣滲透的影響。
    3. 偵測器背面使用POCl3預置擴散驅入會得到比較好的元件特性。
    其次,我們也設計數種不同的測試元件(test-key)來討論防護圈(guard-ring)結構和圖形對元件漏電流和崩潰電壓的影響。實驗結果顯示防護圈可以增加元件崩潰電壓﹔在元件轉角部份,使用圓角會比使用直角好。
    本大面積矽偵測器已通過歐洲粒子加速中心(CERN)的測試,並且獲得量產的機會。



    Five different processes had been used to fabricate the detectors and the resulted device characteristics were compared. For the front-side process of a detector, the breakdown voltage of a detector was significantly reduced by on the oxide covering the p+-strip, since the oxide layer had a large compressive stress. As to the backside of the detector, using the POCl3 diffusion process could result in a better n+-i junction and hence device performance than using As-implantation process. In addition, although the SiO2/Si3N4 passivation layer also increased the device leakage current due to its stress, but, the detector without passivation layer could not prevent moisture penetration which would increase the device leakage current and reduced the device reliability.
    By using test-keys on processed wafers, the effects of guard-rings on device performance had been studied. The guard-ring could be used to increase the device breakdown voltage, and the detector with rounded corners had the higher breakdown voltage and lower leakage current since the crowding electric-field around corner would be smoothed with rounded corners.

    ABSTRACT III TABLE CAPTIONS IV FIGURE CAPTIONS V Chapter 1 INTRODUCTION 1 Chapter 2 DESIGN CONSIDERATIONS AND FABRICATION PROCESSES 6 2.1 Fundamental Considerations 6 2.2 Design 11 2.3 Processes 12 Chapter 3 STUDIES ON REDUCING LEAKAGE CURRENT AND INCREASING BREAKDOWN VOLTAGE 22 3.1 Sample Preparations 22 3.2 Full-depletion Voltage 23 3.3 Effect of Oxide above P+-strips 24 3.4 Effect of Backside Process 26 3.5 Effect of Passivation 28 3.6 Effect of Junction Depth 29 3.7 Summaries 30 Chapter 4 Test-Keys 45 4.1 Guard Rings 45 4.2 Measurement System 46 4.3 Distance Between Guard-ring and Main Junction 47 4.4 Multiple Guard-rings 48 4.5 Corner Effect 50 4.6 Summaries 50 Chapter 5 CONCLUSIONS 67 REFERENCES 69

    [1] A.H. Walenta,“Principles and New Development of Semiconductor Radiation Detectors”, Nuclear Instruments and Methods in Physics Research A253, pp.558-571, 1987.
    [2] A.C Melissinos, “Experiments in Modern Physics”, Academic Press, Inc., New York, USA, 1989.
    [3] G.F. Knoll, “Radiation Detection and Measurement”, 2nd ed., John Wiley & Sons, Inc., New York, USA, 1989.
    [4] S.M. Sze, “Semiconductor Sensors”, John Wiley & Sons, Inc., New York, USA, 1994.
    [5] E. Gatti and P. Pehak, “Semiconductor Drift Chamber - an Application of a Novel Charge Transport Scheme”, IEEE Trans. on Electron Devices, ED-29, p.1388, 1982; also Proc. 2nd Pisa Meeting on Advanced Detectors, Grosseto, Italy, in Nuclear Instruments and Methods in Physics Research 225, pp.608-614, 1984.
    [6] E. Gatti, P. Rehak, and J. T. Walton, “Silicon Drift Chamber First Results and Optimum Processing of Signals”, Nuclear Instruments and Methods in Physics Research 226, pp.129-141, 1984.
    [7] L. Struder, P. Holl, G. Lutz, and J. Kemmer, “Device Modeling of Fully Depletable CCDs”, Nuclear Instruments and Methods in Physics Research A253, pp.386-392, 1987.
    [8] V. Radeka, P. Rehak, S. Rescia, E. Gatti, A. Longoni, M. Sampietro, G. Bertuccio, P. Holl, L. Struder, and J. Kemmer, “Implanted Silicon JFET on Completely Depleted High-Resistivity Devices”, IEEE Electron Device Letters, Vol. 10, pp.91-93, 1989.
    [9] J. Kemmer and G. Lutz, “New Structures for Position Sensitive Semiconductor Detectors”, Nuclear Instruments and Methods in Physics Research A273, pp.588-598, 1988.
    [10] H.Becker, T.Boulos, P. Cattaneo, H. Dietl, D. Hauff,E. Lange, G. Lutz, H. G. Meser, A.S. Schwartz, R. Settles, L. Struder, J. Kemmrr, U. Prechtel, T. Ziemann, and W. Buttler, “New Developments in Double Sided Strip Detectors”, IEEE Trans. On Nuclear Science, Vol. 37, pp.101-106, 1990.
    [11] Alvsvaag, S.J.; Maeland, O.A.; Klovning, A.; Benvenuti, A.C.; Giordano, T.; Guerzoni, M.; Navarria, F.L.; Verardi, M.G.; Camporesi, T.; Vallazza, E.; Bozzo, M.; Cereseto, R.; Barreira, G.; Espirito Santo, M.C.; Maio, A.; Onofre, A.; Peralta, L.; Pimenta, “A silicon pad shower maximum detector for a "Shashlik" calorimeter “IEEE Trans. On Nuclear Science, Vol.42, No.4, pp. 469-473, 1995.
    [12] Avrillon, S.; Ikeda, H.; Matsuda, T.; Asano, Y.; Tsuchiya, S.; Saitoh, Y.; Inoue, M.; Yamanaka, J. “Performance of a pMOS pixel to be used in radiation detectors “, IEEE Trans. On Nuclear Science, Vol.43, No.3, pp. 1161-1164, 1996.
    [13] Passeri, D.; Ciampolini, P.; Baroncini, M.; Santocchia, A.; Bilei, G.M.; Checcucci, B.; Fiandrini, E, “Comprehensive modeling of silicon microstrip detectors “, IEEE Trans. On Nuclear Science, Vol.44, No.3, pp. 598-605, 1997.
    [14] G.Batignani, L. Bosisio, A. Conti, E. Focardi, F. Forti, M. A. Giorgi, M. Grandi, G. Parrini, P. Tempesta, G. Tonelli, and G. Triggiani, “Test Results on Double-Side Readout Silicon Strip Detectors”, IEEE Trans. On Nuclear Science, Vol.36, pp. 40-45, 1989.
    [15] Saitoh, Y.; Akamine, T.; Inoue, M.; Yamanaka, J.; Kadoi, K.; Takano, R.; Kojima, Y.; Miyahara, S.; Kamiya, M.; Ikeda, H.; Matsuda, T.; Tsuboyama, T.; Ozaki, H.; Tanaka, M.; Iwasaki, H.; Haba, J.; Higashi, Y.; Yamada, Y.; Okuno, S.; Avrillon, S.; Nemoto, T, ” Fabrication of a double-sided silicon microstrip detector with an ONO capacitor dielectric film”, IEEE Trans. On Nuclear Science, Vol.43, No.3 pp. 1123-1129, 1996.
    [16] Iwata, Y.; Ohsugi, T.; Fujita, K.; Kitabayashi, H.; Yamamoto, K.; Yamamura, K.; Unno, Y.; Kondo, T.; Terada, S.; Kohriki, T.; Asai, M.; Nakano, I.; Takashima, R., “Optimal p-stop pattern for the N-side strip isolation of silicon microstrip detectors”, IEEE Trans. On Nuclear Science, Vol.45, No.3, pp. 303-309, 1998.
    [17] Saitoh, Y.; Akamine, T.; Inoue, M.; Yamanaka, J.; Echigo, N.; Miyahara, S.; Kamiya, M.; Ikeda, H.; Matsuda, T.; Bozek, A.; Haba, J.; Koike, S.; Ozaki, H.; Tanaka, M.; Iwasaki, H.; Higashi, Y.; Tsuboyama, T.; Yamada, Y.; Banas, E.; Natkaniec, Z.; Palka, H., “ Performance of a double-sided silicon microstrip detector with a wide-pitch N-side readout using a field-plate and a multi P-stop structure“, Conference Record of IEEE 1996 Nuclear Science Symposium conference, Vol. 1, pp. 181 -185, 1996
    [18] Tsuboyama, T.; Haba, J.; Ikeda, H.; Iwasaki, H.; Matsuda, T.; Ozaki, H.; Tanaka, M.; Yamada, Y.; Saito, Y.; Akamine, K.; Inoue, M.; Yamanaka, J.; Kadoi, K.; Takano, R.; Kojima, Y.; Miyahara, S.; Kamiya, M.; Okuno, S.; Avrillon, S.; Hazumi, M.; Nagashima, “Test of a double-sided double-metal silicon microstrip detector with an ONO insulator, “Conference Record of IEEE 1995 Nuclear Science Symposium and Medical Imaging Conference Vol. 1 , pp. 192 —195,1995
    [19] Alexander, J.P.; Bebek, C.J.; Browder, T.E.; Dobbins, J.A.; Gray, S.G.; Honscheid, K.; Jones, C.D.; Katayama, N.; Katris, J.S.; Kim, P.C.; Selen, M.; Worden, H.M.; Wurthwein, F.; Gronberg, J.; Morrison, R.J.; Hale, D.L.; Korte, C.; Kyre, S.; Nelson, H.N.; “Studies of double-sided, double-metal silicon microstrip detectors”, Conference Record of IEEE 1992 Nuclear Science Symposium and Medical Imaging Conference Vol. 1, pp. 224 -226, 1992
    [20] P. Wertelaers, “ ECAL Preshower” CMS project meeting at CERN, November 28, 2000
    [21] Warner Ten Kate, “The Silicon microstrip detector”. (a copy of transparencies)
    [22] B. Hyams, U. Koetz, E. Belau, R. Klanner, G. Lutz, E. Neugebauer, A. Wylie and J. Kemmcr, “A Silicon Counter Telescope to Study Short-lived Particles in High-energy Hadronic Interactions”, Nuclear Instruments and Methods in Physics Research 205, pp.99-105, 1983.
    [23] S.M. Sze, “Physics of Semiconductor Devices”, John Wiley & Sons, Inc., New York, USA, 1981.
    [24] M. Campanella,N. Croitoru, F. Groppi, F. Lemeilleur, S. Pensotti, P. G. Rancoita, and A. Seidman, “The Effect of Radiation on Ion-Implanted Silicon Detectors”, Nuclear Instruments and Methods in Physics Research A243, pp.93-97, 1986.
    [25] G. Batignani, L. Bosiso, E. Forcardi, F. Forti, M. A. Giorgi, L. Moneta, G. Parrini, G. Tonelli, and G. Triggiani, “Development and Performance of Double Sided Silicon Strip Detecrors”, Nuclear Instruments and Methods in Physics Research A310, pp.160-164. 1991.
    [26] P. Hell, J. Kemrner, U. Prrchtel, T. Ziemann, D. Hauff, G. Lutz, A. S. Schwarz, and L. Struder, “A Double-Sided Silicon Strip Detector with Capacitive Readout and a New Method of Integrated Bias Coupling”, IEEE Trans. On Nuclear Science, Vol. 36, pp.251-255, 1989.
    [27] W. T. Lin, Y. H. Chang, A. E. Chen, K. T. Huang, and W. C. Tsay, “PHOSBOS Silicon Sensor Production at NCU”, PHOROS project review of quarter 2, National Brookhaven Laboratory, June 18, 1997.
    [28] B. J. Baliga, “ Modern Power Devices”, John Wiley & Sons, Inc., New York, USA, 1987.
    [29] Wen-Chin Tsay; Jyh-Wong Hong; Chen, A.; Lin, W.T.; Hsien-Ten Ting; Song-Tsang Chiang; Ching-Lan Yen, “ONO SMD - A silicon microstrip detector with ONO A-C coupled capacitor”, Electron Devices and Materials Symposium, EDMS, pp. 6-8-29 -6-8-32 , 1994
    [30] Wen-Chin Tsay, Jyh-Wong Hong, Y.H.Chang, A.Chen, S.R.Hou, S.L.Hsu, C.H.Lin, Willis T.Lin, Hsien-Jen Ting, Song-Tsang Chiang, Emily Chuang, and Su-Wen Hwang, “Studies of Large- Area Silicon Microstrip Sensors”, IEEE Trans. On Nuclear Science, Vol.42, No.4, pp. 437-440, 1995.
    [31] R. A. Craven and H. W. Korb, “Internal Gettering in Silicon”, Solid State Technology, pp.55-61, July, 1981.
    [32] Wen-Chin Tsay; Yen-Ann Chen; Li-Hong Laih; Jyh-Wong Hong; Chen, A.E.; Lin, W.T.; Yuan-Hann Chang; Hou, S.R.; Chung-Ren Li; Hsien-Jen Ting; Wei-Chen Liang; Cheng, C.C.P.; Song-Tsang Chiang, “Studies on reducing leakage current of large-area silicon microstrip sensors”, IEEE Trans. On Nuclear Science, Vol.45, No.2, pp. 186-194, 1998.
    [33] S. M. Hu and R. O. Schwenker, “Effects of Ion Implantation on Substrate Hardening and Film Stress Reducing and Their Effect on the Yield of Bipolar Transistors”, J.Appl. Phys., Vol.49, pp.3259-3265, 1978.
    [34] Y. C. Kao and E. D. Wolley, “High Voltage Planar p-n Junctions,” Proc. IEEE, 55, 1490-1414 (1967).
    [35] L. Evensen, A. Hanneborg, B. S. Avest, and M. Nese, “Guard Ring Design for High Voltage Operation of Silicon Detectors”, Nuclear Instruments and Methods in Physics Research A337, pp.44-52, 1993.
    [36] Da Rold, M.; Paccagnella, A.; Da Re, A.; Verzellesi, G.; Bacchetta, N.; Wheadon, R.; Dalla Betta, G.-F.; Candelori, A.; Soncini, G.; Bisello, D, “Radiation effects on breakdown characteristics of multiguarded devices “IEEE Trans. On Nuclear Science, Vol.44, No.3, pp. 721-727, 1997.
    [37] Li, Z.; Huang, W.; Zhao, L.J., “Study of the correlation between the cutting edge current breakdown and the simulated lateral electrical field boundary in high resistivity silicon detectors with multi-guard ring structure “, IEEE Trans. On Nuclear Science, Vol.47, No.3, pp. 729-736, 2000.

    QR CODE
    :::