使用DVD光學讀取頭在角度與位移量測之改良研究

簡易檢索 / 詳目顯示

回結果列表

研究生：	劉焜地 Kun-Di Liu
論文名稱：	使用DVD光學讀取頭在角度與位移量測之改良研究 The improvement of research of DVD optical pick-up head at the displacement and tilt measurements.
指導教授：	孫文信 Wen-Shing Sun
口試委員:
學位類別：	碩士 Master
系所名稱：	理學院 - 光電科學與工程學系 Department of Optics and Photonics
畢業學年度：	97
語文別：	中文
論文頁數：	86
中文關鍵詞：	角度與位移量測、原子力顯微鏡、光學讀寫頭
外文關鍵詞：	tilt and displacement, AFM, Pick-up head, DVD
相關次數：	點閱：12 下載：0
分享至:	分享至facebook 分享至twitter

查詢本校圖書館目錄查詢臺灣博碩士論文知識加值系統勘誤回報

本論文提出三種改良型光學讀取頭設計，取代傾斜45度平板分光鏡之光學讀取頭，應用於量測待測面有角度變化與縱向位移時之訊號模擬與分析，線性量測範圍可增加至8μm左右，且能有效減少角度變化對位移訊號的誤差，並提升不同方位角的可判讀性。在應用上能精準的得到待側面的表面輪廓，而結合光學讀取頭量測系統可用於測量原子力顯微鏡懸臂位移與角度變化，除了具有高解析度外，結構也十分精巧且價格低廉，未來更可以隨著讀取頭性能的進化而提升整個量測系統的精確性。

The present papers proposed that three kinds of improvement optical pick-up head design, to substitution pick-up head with inclined of 45 degree plate beamsplitter, and apply to measure the tilt angles and the longitudinal displacements in the gauging testing surface, with the signal simulation and analysis. The linear gauging range can increase to about 8μm, and reduce the angle tilt effectively to the displacement signal, promotes the interpretability for different azimuth.
The new design form can obtain in the application scans the side the surface profile, and be possible to unifies optical pick-up head gauging system into the atomic force microscope used in surveying the displacement and the tilt angle of the cantilever, besides has the fine resolution, the structure is also very exquisite, and the low in price, may promote the entire gauging system''s accuracy in the future along with the performance evolution of the optical pick-up head.

摘 要....................................................................................................................I
Abstract...............................................................................................................II
致謝....................................................................................................................III
目 錄.................................................................................................................IV
表 目 錄.........................................................................................................VI
圖 目 錄.......................................................................................................VII
第一章 前言..................................................................................................1
1-1 研究背景..........................................................................................1
1-2 研究動機..........................................................................................4
1-3 文獻回顧..........................................................................................4
1-4 論文架構..........................................................................................6
第二章 光學讀取頭與量測原理..................................................................7
2-1 光學讀取頭......................................................................................7
2-2 使用像散法之聚焦誤差訊號分析................................................12
2-3 反射面方位角與角度訊號............................................................14
2-4 傾斜45度平板分光鏡光學讀取頭訊號分析..............................15
2-5 結論................................................................................................24
第三章 柱面鏡像散法之光學讀取頭模擬................................................25
3-1 光學系統模擬................................................................................25
3-2 聚焦誤差訊號分析........................................................................26
3-3 角度訊號分析................................................................................28
3-4 結論................................................................................................40
第四章 Pigtailed laser diode 之光學讀取頭模擬...................................41
4-1 光纖傳遞原理................................................................................41
4-2 光學系統架構................................................................................43
4-3 聚焦誤差訊號分析........................................................................45
4-4 角度訊號分析................................................................................46
4-5 結論................................................................................................58
第五章 使用擴束準直鏡之光學讀取頭模擬............................................59
5-1 擴束準直鏡設計............................................................................59
5-2 光學讀取頭系統............................................................................63
5-3 聚焦誤差訊號分析........................................................................66
5-4 角度訊號分析................................................................................67
第六章 結論與未來展望............................................................................79
參考文獻.............................................................................................................81
附錄.....................................................................................................................84

                                

[1] G. Binning, H. Rohrer, CH. Gerber, E. Weibel, “Surface studies by scanning tunneling microscopy,“ Phys. Rev. Lett., Vol. 49, pp.57-61, (1982).
[2] G. Binning, C.F. Quate, CH. Gerber, “Atomic Force Microscope, “ Phys. Rev. Lett., Vol. 56, pp.930-933, (1986).
[3] S. Ura, T. Suhara, H. Nishihara, and J. Koyama, “An integrated-optic disk pickup device,” Electronics and Communications in Japan, Part 2, Vol. 70, No. 2, (1987).
[4] J. Benshop, and G. van Rosmalen, “Confocal compact scanning optical microscope based on compact disc technology,” Appl. Opt., 30, 1179-1184, (1991).
[5] T. R. Armstrong, and M. P. Fitzerald, “An autocollimator based on the laser head of a compact disc player,” Meas. Sci. Technol., 3, 1072-1076, (1992).
[6] A. JC Brown, “High speed optical measurement of 3D surface,” Proc. SPIE 2088, 190-194, (1993).
[7] J. H. Zhang, and L. L. Cai, “An autofocusing measurement system with a piezoelectric translator,” IEEE/ASME Transactions on Mechatronics 2, 213-216, (1997).
[8] J. H. Zhang, and L. L. Cai, “Profilometry using an optical stylus with interferometric readout,” Meas. Sci. Technol. 8, 546-549, (1997).
[9] C. During, T. Komeda, M. Matsuto, and H. Funakubo, “An inexpensive light source and detector module for fiber-optic measurements,” Meas. Sci. Technol. 8, 209-212, (1997).
[10] K. Ehrmann, A. Ho, and K. Schindhelm, “A 3D optical profilometer using a compact disc reading head,” Meas. Sci. Technol. 9, 1259-1265, (1998).
[11] F. Quercioli, B. Tiribilli, C. Ascoli, P. Baschieri, and Frediani, “Monitoring of an atomic force microscope cantilever with a compact disk pickup,” Review of Scientific Instruments, Vol. 70, NO.9, (1999).
[12] K. C. Fan, C. Y. Lin, and L. H. Shyu, “The development of a low-cost focusing probe for profile measurement,” Meas. Sci. Technol. 11, N1-N7, (2000).
[13] K. C. Fan, C. L. Chu, J. L. Liao, and J. I. Mou, “Development of a high-precision straightness measuring system with DVD pick-up head,” Meas. Sci. Technol. 14, 47-54, (2003).
[14] E. T. Hwu, K. Y. Huang, S. K. Hung, C.W. Yang, and I. S. Hwang, “Simultaneous detection of translational and angular displacements of micromachined elements“ Jpn. J. Appl. Phys. 91, 221908, (2007).
[15] E. T. Hwu, S. K. Hung, C.W. Yang, K. Y. Huang, and I. S. Hwang, “Real-time detection of linear and angular displacements with a modified DVD optical head” Nat. Nanotechnol, 19, 115501, (2008).
[16] 楊家逢，「模組化雙波長光學讀寫頭的設計與光學讀寫頭應用在角度量測的研究」，國立中央大學光電科學與工程學系，碩士論文，Taiwan(2007)
[17] Joseph W. Goodman, “Introduce To Fourier Optics”, The McGraw-Hill Companies, Inc., 2002.
[18] Warren J. Smith, “Modern Optical Engineering- The Design of Optical Systems”, The McGraw-Hill Companies, Inc., 2000.
[19] D. K. Cohen, W. H. Gee, M. Ludeke, J. Lewkowicz, “Automatic focus control: the astigmatic lens approach”, Appl. Opt., Vol. 30, NO. 4 565-570, (1984).
[20] 謝東益，「利用Pigtailed Laser Diode 光學讀寫頭在角度與位移量測之研究」，國立中央大學光電科學與工程學系，碩士論文，Taiwan(2008)
[21] B. E. A. Saleh, M. C. Teich, “Fundamentals of Photonics, 2nd Edition”, John Wiley & Sous Companies, Inc., 1991.
[22] Thorlb, Inc., http://www.thorlabs.com/navigation.cfm?Guide_ID=26
[23] W.S. Sun, K.D. Liu, J.W. Pan, C.L. Tien, and M.S. Hsieh, “Laser expander design of highly efficient Blu-ray disc pickup head” Optics Express, Vol. 17, NO. 4, 2235, (2009).

簡易檢索 / 詳目顯示

相關論文