跳到主要內容

簡易檢索 / 詳目顯示

回結果列表
研究生： 雅斯帝
Tyas Dwi Aprilniadi
論文名稱： Internal Structure and Permeability of the Creeping Chihshang Fault, Taiwan
指導教授： 郭力維
Li-Wei Kuo
口試委員:
學位類別： 碩士
Master
系所名稱： 地球科學學院 - 地球科學學系
Department of Earth Sciences
論文出版年： 2019
畢業學年度： 107
語文別： 英文
論文頁數： 90
中文關鍵詞： 匍匐池上斷層 、Lichi Mélange 、滲透率各向異性
外文關鍵詞： Creeping Chihshang Fault, LichiMélange, permeability anisotropy
相關次數： 點閱：19  下載：0 
分享至:
查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報

    • 斷層帶之滲透率與內部結構主要控制上部地殼的流體流動。斷層帶可作為阻水帶或導水帶，其滲透率支配流體穿過或沿著斷層遷移，且能與圍岩之滲透率有很大差距。在此，我們研究池上斷層之滲透率與內部結構，我們利用高圍壓孔隙滲透儀(YOKO2)對立吉混同層及礫石層進行滲透率與孔隙率之量測，實驗條件為室溫、均向圍壓、孔隙流體為氦氣。我們利用萬安二號井的岩心，考慮滲透率異向性，製成垂直和平行斷層面之圓柱試體，及垂直和平行地表之圓柱試體。結果顯示，於低圍壓下，利吉層之滲透率應力敏感度相當高，較礫石層之滲透率低；利吉層孔隙率則明顯低礫石層。此一結果能說明潛移行為的季節性變化。我們亦進行微構造觀察及分析，瞭解微裂隙(microcrack)如何影響滲透率。根據滲透率量測、微構造觀察結果，我們提出池上斷層之內部構造與滲透率構造。

    Internal structure and permeability structure of fault zone primarily control on fluid flow in upper crust. It indicates faults as the conduct or barrier, dictates fluid flow along or across faults and can be largely different from those of surrounding country rocks. To consider the relation between internal structure and permeability structure in the Chihshang Fault, we performed permeability and porosity measurements on the Lichi Mélange and the Conglomerate. We measured permeability and porosity with an intra-vessel oil pressure apparatus (YOKO2) at room temperature at isotropic confining pressure, using helium as pore fluid. Cylindrical samples were made from retrieved rock cores in WAN-2 borehole sample which represents a borehole sample near the Chihshang fault. The samples were made in dip and normal direction of fault plane, and also in vertical and horizontal direction to investigate the permeability anisotropy. The results showed the Lichi Mélange is impermeable that may be responsible for seasonal fluctuation on creeping Chihshang fault. We conducted the microfratures analysis, used polarizing microscopy to investigate how microstructures influence the permeability of samples. Based on the microstructures, permeability anisotropy and the fault zone architecture we proposed the permeability structures of Chihshang fault to provide the summary of measured results.

    TABLE OF CONTENTS 摘要 i ABSTRACT. ii ACKNOWLEDGMENTS. iii TABLE OF CONTENTS iv LIST OF FIGURES vi LIST OF TABLES ix Chapter 1 INTRODUCTION 1 1.1 The permeability in fault zone. 1 1.2 The Chihshang Fault in eastern Taiwan 3 1.3 The pressure-solution creep. 7 1.4 The framework 8 Chapter 2 SAMPLE PREPARATION AND METHODOLOGY. 10 2.1 Samples Preparation 10 2.2 Permeability and Porosity Measurements 19 2.3 Fracture description 22 2.4 Microstructural observations 22 Chapter 3 RESULTS 23 3.1 Permeability evolution with confining pressure in laboratory 23 3.2 Porosity evolution with confining pressure in laboratory 26 3.3 Qualitative Fractures Description 27 3.3.1 Fractures description of rock cores 28 3.3.2 Optical photomicrographs of samples from WAN-2 borehole (the fragment in vicinity of the experimental sample) 32 3.3.3 Optical photomicrographs from permeability samples after measurement 42 Chapter 4 DISCUSSION 62 4.1 Comparison between laboratory and injection experiments 62 4.2 Effect of stress on permeability in the Chihshang Fault. 63 4.3 The permeability anisotropy in the Chihshang Fault 66 4.4 The relationship between permeability and porosity 69 4.5 Permeability structure along WAN-2 and the correlation with the creeping mechanism 70 Chapter 5 CONCLUSIONS 73 REFERENCES. 74 LIST OF FIGURES Fig. 1.1. The simplified fault model proposed by Caine et al. (1996) 2 Fig. 1.2. The tectonic setting of Taiwan 4 Fig. 1.3. Tectonic setting of Taiwan and geological region of Coastal Range 6 Fig. 1.4. The illustration of the fracturing and fragmentation process in the fault gouge after an earthquake 8 Fig. 1.5 Drilling boreholes and the rock core 9 Fig. 2.1. The sampling direction for the Lichi Mélange and the Conglomerate 10 Fig. 2.2. YOKO2 used in this study to measure permeability and porosity 19 Fig. 2.3. The illustration of permeability and porosity measurement systems 21 Fig. 3.1. Cycling confining pressure experiment in the Lichi Mélange 23 Fig. 3.2. Permeability data of the Lichi Mélange 24 Fig. 3.3. Permeability data of the Conglomerate 25 Fig. 3.4. Porosity data of the Lichi Mélange. 26 Fig. 3.5. Porosity data of the Conglomerate 27 Fig. 3.6. The sketch of rock cores at 13.4-30.0 m depth. 29 Fig. 3.7. The sketch of rock cores at 44.2-62.0 m depth. 30 Fig. 3.8. The sketch of rock cores at 45.0-47.0 m depth. 31 Fig. 3.9. The thin section of LPe01. 32 Fig. 3.10. The thin section of LPe02. 33 Fig. 3.11. The thin section of LPe04. 34 Fig. 3.12. The thin section of LPa04. 35 Fig. 3.13. The thin section of LPa05. 36 Fig. 3.14. The thin section of LPe05. 37 Fig. 3.15. The thin section of CV13. 38 Fig. 3.16. The thin section of CH13. 39 Fig. 3.17. The thin section of CV14. 40 Fig. 3.18. The thin section of CV15. 41 Fig. 3.19. The thin section of CH15. 42 Fig. 3.20. The thin section of KLPe01. 43 Fig. 3.21. The thin section of KLPe02. 44 Fig. 3.22. The thin section of KLPe04. 45 Fig. 3.23. The thin section of KLPa04. 46 Fig. 3.24. The thin section of KLPa05. 47 Fig. 3.25. The thin section of KLPe05. 48 Fig. 3.26. The thin section of KLV07. 49 Fig. 3.27. The thin section of KLH09. 50 Fig. 3.28. The thin section of KLPa10_1. 51 Fig. 3.29. The thin section of KLPe10 52 Fig. 3.30. The thin section of KLPa10_2 53 Fig. 3.31. The thin section of KLPa11 54 Fig. 3.32. The thin section of KCPe12 55 Fig. 3.33. The thin section of KCPa12 56 Fig. 3.34. The thin section of KCH13 57 Fig. 3.35. The thin section of KCV13. 58 Fig. 3.36. The thin section of KCV15. 59 Fig. 3.37. The thin section of KCH15. 60 Fig. 3.38. The thin section of KCV16. 61 Fig. 4.1. The elastic deformation in the cycling confining pressure experiment 64 Figure 4.2. The stress sensitivity comparison between permeability and porosity of the Lichi Mélange 65 Fig. 4.3. The comparison of the Lichi Mélange in parallel-fault and perpendicular-fault permeability 66 Fig. 4.4. The petrographic analysis which showed unclear foliation in parallel-fault direction 67 Fig. 4.5. The similarity of the microfractures in vertical and horizontal direction 67 Fig. 4.6. The Conglomerate sample in parallel-fault and perpendicular-fault 68 Fig. 4.7. The permeability and porosity relationship 69 Fig. 4.8. The comparison of the petrographic analysis between LPe02 and CH13 70 Fig. 4.9. The permeability structure along the WAN-2 71

    Armitage, P. J., Faulkner, D. R., Worden, R. H., Aplin, A. C., Butcher, A. R., and Iliffe, J., 2011. Experimental measurement of, and controls on, permeability and permeability anisotropy of caprocks from the CO2 storage project at the Krechba Field, Algeria. Journal of Geophysics Research, v. 116, B12208, doi: 10.1029/2011JB008385.
    Aydin, A., 1978. Small faults as deformation bands in sandstone. Pure and Applied Geophysics, v. 116, p. 913-93.
    Caine, J. S., Evans, J. P., and Forster, C. B., 1996. Fault zone architecture and permeability structure. Geology, v. 24, p. 1025-1028.
    Chang, C., Angelier, J., Huang, C., and Liu, C., 2001. Structural evolution and significance of a mélange in a collision belt: The Lichi Mélange and the Taiwan arc–continent collision. Geological Magazine, v. 138, p. 633-651. doi: 10.1017/S0016756801005970.
    Chen, W.-S. 2009. The fault slip long term velocity and recurrence period. Report of Central Geological Survey, p. 31-40.
    Chester, F.M., and Logan, J.M., 1986. Implications for mechanical-properties of brittle faults from observations of the Punchbowl fault zone, California. Pure and Applied Geophysics, v. 124 (1-2), p. 79-106.
    David, C., Wong, T., Zhu, W., and Zhang, J., 1994. Laboratory measurement of compaction-induced permeability change in porous rocks: implications for the generation and maintenance of pore pressure excess in the crust. Pure and Applied Geophysics, v. 143, p. 425-456.
    Evans, J. P., Forster, C. B., and Goddard, J. V., 1997. Permeability of fault-related rocks, and implications for hydraulic structure of fault zones. Journal of Structural Geology, v. 19, p. 1939-1404.
    Faulkner, D. R., and Rutter, E. H., 1998. The gas permeability of clay-bearing fault gouge at 20°C. Geological Society of London, v. 147, p. 147-156. doi: 10.1144/GSL.SP.1998.147.01.10.
    Faulkner, D., Jackson, C., Lunn, R., Schlische, R., Shipton, Z., Wibberley, C., and Withjack, M., 2010. A review of recent developments concerning the structure, mechanics and fluid flow properties of fault zones. Journal of Structure Geology, v. 32, p. 1557-1575. doi: 10.1016/j.jsg.2010.06.009.
    Gibson, R. G., 1994. Fault-zone seals in siliciclastic strata of the Columbus Basin, offshore Trinidad. AAPG Bulletin, v. 78, p. 372-1385.
    Gratier, J-P., Guiguet, R., Renard, F., and Jenatton, L., 2009. A pressure solution creep law for quartz from indentation experiments. Journal of Geophysical Research, v. 114. doi: 10.1029/2008JB005652
    Hao, K., Wu, Y.-M., Chen, Y.-G., and Chen, R.-Y., 2007. 2003 Mw6.8 Chengkung earthquake and its related seismogenic structures. Journal of Asian Earth Sciences, v. 31, n. 3, p. 332-339. doi: 10.1016/j.jseaes.2006.07.028.
    Huang, C.-Y., Chien, C.-W., Yoi, B., and Chang, C.-P. 2008. The Lichi Mélange: A collision mélange formation along early arc ward back thrusts during fore arc basin closure, Taiwan arc-continent collision. A. E. Draut, P. D. Clift, D. W. Scholl (eds.), Formation and Applications of the Sedimentary Record in Arc Collision Zones, The Geological Society of America, p. 127-154. doi: 10.1130/2008.2436(06).
    Lee, J.-C., Angelier, J., Chu, H.-T., Hu, J.-C., and Jeng, F.-S., 2003. Active fault creep variations at Chihshang, Taiwan, revealed by creep meter monitoring, 1998-2001. Journal of Geophysical Research, v. 108., n. B11, 2528. doi: 10.1029/2003JB002394.
    Lee, J.-C., Chu, H.-T., Angelier, J., Hu, J.-C., and Chen, H.-Y., 2006. Quantitative analysis of surface coseismic faulting and post seismic creep accompanying the 2003, Mw = 6.5, Chengkung earthquake in eastern Taiwan. Journal of Geophysical Research, v. 111. doi:10.1029/2005JB003612.
    Mizoguchi, K., Hirose, T., Shimamoto, T., and Fukuyama, E., 2008. Internal structure and permeability of the Nojima fault, southwest Japan. Journal of Structural Geology, v. 30 (4), p. 513-524.
    Morrow, C. A., Lockner, D., Hickman, S., Rusanov, M., and Rockel. T., 1994. Effects of lithology and depth on the permeability of core samples from the Kola and KTB drillholes. Journal of Geophysics Research, v. 99, p. 7274-7623.
    Morrow, C., Lockner, D., Moore, D., and Hickman, S, 2014. Deep permeability of the San Andreas Fault from San Andreas Fault Observatory at Depth (SAFOD) core samples. Journal of Structural Geology, v. 64, p. 99-114. doi: 10.1016/j.jsg.2013.09.009
    Mu, C.-H., 2012. Shallow Geological Structure and hydromechanical behavior of an active reverse fault at convergent plate boundary: The Chihshang Fault, eastern Taiwan, PhD thesis, National Central University, Taiwan.
    Mu, C.-H., Angelier, J., Lee, J.-C., Chu, H.-T., and Dong, J.-J., 2011. Structure and Holocene evolution of an active creeping thrust fault: The Chihshang fault at Chinyuan (Taiwan). Journal of Structural Geology, v. 33, p. 743-755. doi: 10.1016/j.jsg.2011.01.015

    Mu, C.-H., Lee, J.-C., Guglielmi, Y., 2014 Active fault zone as a barrier of hydraulic conduits in shallow aquifers: insights from on-site injection experiments at the Chihshang fault in eastern Taiwan. AGU Fall Meeting 2014. San Francisco, 17 December 2014.
    Rice, J. R., 1992. Fault stress states, pore pressure distributions, and the weakness of the San Andreas Fault, in Fault Mechanics and Transport Properties of Rocks. International Geophysics Series, v. 51.
    Scheidegger, A. E., 1974. The physics of flow through porous media, 3rd ed., University of Toronto Press, Toronto, Canada.
    Sibson, R. H., 1973. Interactions between temperature and pore-fluid pressure during earthquake faulting and a mechanism for partial or total stress relief. Nature, v. 243, p. 66-68.
    Walder, J., and Nur, A., 1984. Porosity reduction and crustal pore pressure development. Journal of Geophysical Research, v. 89. p. 11,539-11,548.
    Wibberley, C. A., and Shimamoto, T., 2003. Internal structure and permeability of major strike-slip fault zones: The Median Tectonic Line in Mie Perfecture, Southwest Japan. Journal of Structural Geology, v. 25, p. 59-78.
    Wu, W.-J., 2015. Stress-history dependent porosity and permeability in siliciclastic sedimentary rocks – from laboratory tests to in-situ applications, PhD thesis, National Central University, Taiwan.
    Yu, S.-B., Chen, H.-Y., and Kuo, L.-C., 1997. Velocity field of GPS stations in the Taiwan area. Tectonophysics, v. 274, p. 41-59.
    Zhang, S., and Tullis, T., 1998. The effect of fault slip on permeability anisotropy in quartz gouge. Tectonophysics, v. 295 (1-2), p. 41-52. doi: 10.1016/S0040-1951(98)00114-0.
    Zoback, M. D., and H.-P. Harjes, 1997. Injection-induced earthquakes and crustal stress at 9 km depth at the KTB deep drilling site, Germany. Journal of Geophysics Research, v.102, p. 477-492.

    QR CODE
    :::