本文是以實驗探討板材之非對稱輥軋，在於不同輥輪周速比及縮減率下其輥軋力、輥軋扭矩和成形板材的彎曲曲率的變化情形。實驗條件為同徑不同周速比，並包含輥輪與板材間的界面摩擦狀態、初始板厚及平均輥輪直徑的不同等。
於非對稱輥軋後之板材易產生曲率彎曲現象而造成產品品質降低及設備損壞。藉由本實驗所規劃的加工參數，可得知輥軋後板材曲率彎曲行為受縮減率、異周速比及介面摩擦等的影響趨勢，探討出板材在其加工參數下之平坦區曲率值±0.0025(1/mm)的條件。藉以達到曲率控制，減少輥軋道次，以其達到加工能量需求較低之經濟性制程。

This paper discusses rolling load, rolling torque and curvature ratio with different rolling speed ratio and reduction at asymmetrical rolling. The experimental conditions include different initial flat thickness and interface between rolling and specimens by lubrication or dry friction and average diameter of the different roller.
By processing parameters can find out specimens that become curvature turn up or turn down behavior with different reduction, different rolling speed, interface friction and different flat thickness after rolling process. Try to find out the flat area that curvature between 0.0025(1/mm). For the purpose of control the curvature and decrease rolling pass times that can reach lower economical production process.

[1] 王向红、李生智、胡宝明及彭宪廷，”不对称异径三辊轧机热连轧薄带的新技术”，自然科学版16(1)，东北大学学报，1995。
[2] 陳遠欣，“A1050P試片經非對稱壓延之彎曲行為的實驗研究”，國立中央大學，碩士論文，2008。
[3] W.C. Yeh, Y.S. Lee, L. chiang, ”Experimental study of A1050P aluminum alloy under asymmetrical rolling”, The 33rd National Conference on Theoretical and Applied Mechanics, 2009.
[4] 許源泉，塑性加工學，全華科技圖書股份有限公司，台北市，2005。
[5] 簡文來，”複合板壓延之有限元素解析及熱間複合板壓延實驗”，國立中山大學，碩士論文，2000。
[6] W.F. Hosford and R.M. Caddell, "Metal forming Mechanics and Metallurgy", Prentice-Hall International, Inc.55-60,1993.
[7] S. Kobayashi, S. I.oh, T. Altan, ”Metal Forming and the Finite –Element Method”, Oxford University Press, New York, 1989.
[8] 余煥騰、陳適範，金屬塑性加工學，修訂二版，全華科技圖書股份有限公司，台北市，2003。
[9] Serope Kalpakjian, Manufacturing Engineering and Technology(3/e)，文京圖書有限公司，台北市，1998。
[10] 康永林，軋制工程學，冶金工業出版社，北京，2004。
[11] W. Johnson and G. Needham, ”Further Experiments In Asymmetrical rolling”, Int. J. Mech. Sci., 8 (February 1966) 433-455.
[12] H. Shiozaki, S. Shinya, M. Mikami, S. Koide, “Experimental Study on the Effects of Differential Roll Speed Ratio on the Rolling Force, Rolling Torque and Forward Slip in Thin Strip Rolling”, 塑性と加工, Vol. 21, p. 1080-1086, 1982.
[13] D. Pan and D. H. Sansome, “An Experimental Study of the Effect of Roll Speed Mismatch on the Rolling Load during the Cold Rolling of the Thin strip “, Journal of Mechanical Working Technology, Vol. 6, p.361-377, 1982.
[14] J. Pospiech, “A Note On The Influence Of Some Factors Affecting Curvature In The Flat Rolling Of Strip“, Journal of Mechanical Working Technology,Vol. 15, p.69-80, 1987.
[15] J. Jeswiet, P.G. Greene, "Experimental measurement of curl in rolling", J. Mater. Proces. Technol., 84,202-209,1998.
[16] Campbell McConnell and J.G. Lenard, "Friction in cold rolling of a low carbon steel with lubricants", Journal of Materials Processing Technology. 99 (2000) 86-93.
[17] A. Nilsson, ”Front-end bending in plate rolling”, Scandinavian Journal of Metallurgy, Vol. 30, p.337-344, 2001.
[18] A.K. Tieu, Y.J. Liu, ”Friction variation in the cold-rolling process”, Tribology International, Vol. 37, p177-183, 2004.
[19] M. Kazeminezhad, A. Karimi Taheri, “A theoretical and experimental investigation on wire flat rolling process using deformation pattern”, Materials and Design, Vol. 26, p.99-103 , 2005.
[20] M. Kazeminezhad, A. Karimi Taheri, “An experimental investigation on the deformation behavior during wire flat rolling process”, Journal of Materials Processing Technology, Vol. 160, p.313-320, 2005.
[21] Sanjeev Das, N.S. Lim, J.B. Seol, H.W. Kim, C.G. Park, ” Effect of the rolling speed on microstructural and mechanical properties of aluminum–magnesium alloys prepared by twin roll casting”, Materials and Design,Vol. 31, p. 1633–1638, 2010.
[22] Makoto Yoshii, Kazuo Ohmori, Tsuneo Seto, Hideyuki Nikaido, Hiroshi Nishizaki, Masatoshi Inoue, ” Analysis of Warping PhenomenonIn Plate Rolling”, ISIJ International, Vol. 31, No. 9, p. 973-978,1991.
[23] Y. M. Hwang, G. Y. Tzou, ”Analytical and experimental study on asymmetrical sheet rolling”, Int. J. Mech. Sci. Vol. 39, No. 3, p.289-303, 1997.
[24] J. -S. Lu, O. -K. Harrer, W. Schwenzfeier, F. D. Fischer, “Analysis of the bending of the rolling material in asymmetrical sheet rolling”, International Journal of Mechanical Sciences, Vol. 42, p. 49-61, 2000.
[25] A. Kawalek, ”Forming of Band Curvature in
Asymmetrical RollingProcess”, Journal of Materials Processing Technology, 155-156, p.2033-2038, 2004.
[26] C.W. Knight a, S.J. Hardy b, “Influence of roll speed mismatch on strip curvature during the roughing stages of a hot rolling mill”, University of Wales Swansea, Journal of Materials Processing Technology, 168, p. 184-188, 2005.
[27] F. Farhat-Nia a, M. Salimi b, “Elasto-plastic finite element simulation of asymmetrical plate rolling using an ALE approach”, Islamic Azad University, Journal of Materials Processing Technology, 177, P. 525–529, 2006.
[28] Michael Lindgren, ” Experimental investigations of the roll load and roll torque when high strength steel is roll formed”, Journal of Materials Processing Technology, 191, p. 44–47, 2007.
[29] S.A.A. Akbari Mousavi, S.M. Ebrahimi, R. Madoliat, ” Three dimensional numerical analyses of asymmetric rolling”, Journal of Materials Processing Technology, 187–188, p. 725–729, 2007.
[30] M. Philipp, W. Schwenzfeier, F.D. Fischer, R. Wodlinger, C. Fischer, ” Front end bending in plate rolling influenced by circumferential speed mismatch and geometry”, Journal of Materials Processing Technology, 184, p. 224–232, 2007.
[31] 金重勳，工程材料，九版修訂，復文書局，台南市，2003。
[32] Designation：E8M-91, Standard Test Methods for Tension Testing of Metallic Materials [Metric], 50-168.
[33] J. G. Lenard, "Friction and Forward Slip in Cold Strip Rolling", Tribology Transactions, Vol. 35, p. 423-428, 1992.